智能制造網APP
智能制造網手機站
智能制造網小程序
智能制造網官微
智能制造網服務號
一、概述Outline
QJ（D/S）DX型精小型氣動橡膠蝶閥是由氣動活塞式執行機構和襯里蝶閥組成，屬旋轉類控制閥。
該產品以壓縮空氣為動力源，接受控制儀表的4-20mA信號（或開關信號），通過電-氣閥門定位器（或電磁閥）實現對閥門的連續調節（或位式控制）。
橡膠襯里蝶閥是一種閥體內腔襯有橡膠的防腐蝕蝶閥?？刂聘g性流體不與閥體接觸，閥體可用普通鑄鐵或碳鋼，由此降低蝶閥的成本。襯里材料有各種橡膠可供選擇，還可更換。
該產品結構簡單，輸出力矩大，性能*。蝶閥通常適用于控制密封要求比較高的腐蝕性流體。
QJ （D / S） DX-type fine small pneumatic rubber valve is pneumatic piston actuator and lining butterfly valve, is a rotary type control valve.
The product is compressed air as power source, to accept 4-20mA control signal meter （or switch signals）, through the electric - gas valve locator （or solenoid valve） to achieve the continuous adjustment of the valve （or bit control）.
Rubber lined butterfly valve is a body cavity lined with rubber anti-corrosion butterfly. Corrosion control and body fluid does not contact the valve body can be an ordinary cast iron or steel, thus reducing the cost of butterfly. There are a variety of rubber lining materials available, can be replaced.
The product is simple, the output torque, and superior performance. Control valve normally sealing requirements for high corrosive fluids.
二、主要技術參數Main technical parameters
| 公稱通徑mm | 50 | 65 | 80 | 100 | 125 | 150 | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 600 | |
| 額定流量系數Kv | 71 | 100 | 198 | 340 | 500 | 770 | 1360 | 2130 | 3060 | 4160 | 5450 | 6900 | 8500 | 12000 | |
| 公稱壓力Mpa | 0.6、1.0、1.6 | ||||||||||||||
| 連接方式 Connection | 對夾式（管道法蘭標準：JB/T79-94、GB9113-2000 Wafer （pipe flange standard: JB/T79-94, GB9113-2000） | ||||||||||||||
| 介質溫度℃ Temperature | -20~+180 | ||||||||||||||
| 輸入信號Input signal | 0.4~0.6Mpa/調節型0.02-0.1Mpa（4-20mA） 0.4 ~ 0.6Mpa / Regulated 0.02-0.1Mpa （4-20mA） | ||||||||||||||
| 額定行程Rated travel | 調節型：70° 切斷型：90° Modulating: 70 ° cut-off: 90 ° | ||||||||||||||
| 環境溫度℃ Temperature | -40~+150、-40~+180 | ||||||||||||||
| 氣源接口 Air Connection | 1/8 ″G 、 NAMUR1/4″G | ||||||||||||||
| 固有流量特性 Inherent flow characteristic | 近似等百分比Approximay equal percentage | ||||||||||||||
|
| |||||||||||||||
| 泄露等級 Leakage level | ANSIB16.104 IV級、VI（軟密封） ANSIB16.104 IV level, VI （soft seal） | ||||||||||||||
注：允許壓差可參照QJD（S）DR型氣動蝶閥該指標
Note: Allow pressure to refer QJD （S） DR pneumatic valve of the indicators
三、性能指標Performance indicators
| 項目Item | 帶定位器指標值Index value with locator | ||
| 基本誤差Basic error% | ±2.5 | ||
| 回差Hysteresis% | 2.5 | ||
| 死區Dead% | 1.0 | ||
| 始終點偏差 Always point deviation% | 氣開 Open air | 始點 Starting point 終點End | ±2.5 |
| ±2.5 | |||
| 氣關 Gas off | 始點 Starting point 終點End | ±2.5 | |
| ±2.5 | |||
四、執行機構轉扭及動作時間Twist and turn actuators operating time
| 執行機構型號AGT | 63×90 | 75×90 | 83×90 | 92×90 | 110×90 | 118×90 | 127×90 | 160×90 | 210×90 | 254×90 | 255×90 | |
| 扭矩N.m | 400Kpa | 23.2 | 40.0 | 56.0 | 77.6 | 112.8 | 168.0 | 220.0 | 440.0 | 948.0 | 1740.0 | 2172.0 |
| 500Kpa | 29.0 | 50.0 | 70.0 | 97.0 | 141.0 | 210.0 | 275.0 | 550.0 | 1185.0 | 2715.5 | 2715.0 | |
| 動作時間（S） | 0.241 | 0.333 | 0.429 | 0.444 | 0.461 | 0.60 | 0.857 | 1.62 | 3.33 | 6.00 | 7.50 | |
注：1、雙作用執行機構在75%負載情況下的動作時間 2、縮短動作時間可允許非標配置
Note: 1, double-acting actuators at 75% load case, the action time of 2 to shorten the operating time to allow non-standard configuration
五、可配附件Available Accessories
調節型：電-氣閥門定位器，空氣過濾減壓器，手輪機構等。
切斷型：定位開關，空氣過濾減壓器，電磁閥，手輪機構等。
Adjustment type: electric - gas valve positioner, air filter regulator, hand wheel institutions.
Cut-off: position switch, air filter regulator, solenoid valve, hand wheel institutions.
六、主要零件材質與內腔襯材料Material of main parts and cavity lining material
| 零件名稱Part Name | 材料Material |
| 閥體Body | 各種橡膠、聚四氟 A variety of rubber, PTFE |
| 蝶板Disc | 灰鑄鐵、球墨鑄鋼、鑄鋼、不銹鋼及特殊材料 Gray cast iron, ductile cast steel, cast steel, stainless steel and special materials |
| 密封圈Ring | 球墨鑄鋼、鑄鋼、合金鋼、不銹鋼 Ductile cast steel, cast steel, alloy steel, stainless steel |
| 閥桿Stem | 2Cr13、不銹鋼 2Cr13, Stainless Steel |
| 填料Filler | O型圈、柔性石墨 O-ring, flexible graphite |
1.閥體內腔襯材料Body cavity lining materials
| 材料品種 Variety of materials | 氯丁橡膠 Neoprene | 丁腈橡膠NBR | 乙丙橡膠EPDM | 硅橡膠Silicone rubber | 氟橡膠Viton |
| 代號Code | X或J | X 或JA | XB或 JB | XD或 JD | XE 或JE |
| 耐zui高溫度 Maximum temperature resistance | 82℃ | 93℃ | 150℃ | 250℃ | 204℃ |
| 耐zui低溫度 Minimum temperature resistance | -40℃ | -40℃ | -40℃ | -70℃ | -23℃ |
| 適用工作溫度 Suitable temperature | ≤65℃ | ≤80℃ | ≤120℃ | ≤200℃ | ≤180℃ |
七、外形尺寸Dimensions
| 標準值Standard value | 參考值Reference | ||||||||
| DN | L | D | D1 | Z-d | H | H0 | A | B | W（kg） |
| 50 | 43 | 99 | 125 | 4-18 | 170 | 130 | 45 | 120 | 24.7 |
| 65 | 46 | 118 | 145 | 4-18 | 170 | 145 | 45 | 120 | 25.6 |
| 80 | 46 | 132 | 160 | 4-18/8-18 | 320 | 186 | 160 | 240 | 27 |
| 100 | 52 | 156 | 180 | 8-18 | 320 | 192 | 310 | 100 | 30.8 |
| 125 | 56 | 184 | 210 | 8-18 | 345 | 200 | 370 | 118 | 37.6 |
| 150 | 56 | 211 | 240 | 8-22 | 385 | 230 | 370 | 118 | 43.2 |
| 200 | 60 | 266 | 295 | 8-22/12-22 | 471 | 297 | 450 | 143 | 100.8 |
| 250 | 68 | 319 | 350 | 12-22 | 533 | 327 | 450 | 143 | 118.5 |
| 300 | 78 | 370 | 400 | 12-22 | 606 | 364 | 535 | 178 | 159 |
| 350 | 78 | 429 | 460 | 16-22 | 694 | 404 | 535 | 178 | 180.7 |
| 400 | 102 | 480 | 515 | 16-26 | 757 | 444 | 630 | 248 | 216.8 |
| 450 | 114 | 530 | 565 | 20-26 | 814 | 472 | 1162 | 232 | 266.1 |
| 500 | 127 | 582 | 620 | 20-26 | 902 | 522 | 1162 | 232 | 325 |
| 600 | 154 | 682 | 725 | 20-30 | 1048 | 590 | 1380 | 318 | 355 |
| 700 | 165 | 794 | 840 | 24-30 | 1277 | 810 | 1380 | 318 | 585 |
| 800 | 190 | 901 | 950 | 24-33 | 1385 | 844 | 1860 | 350 | 798 |
| 900 | 203 | 1001 | 1050 | 28-33 | 1490 | 890 | 1860 | 350 | 906 |
| 1000 | 216 | 1112 | 1160 | 28-36 | 1620 | 950 | 1860 | 350 | 1055 |
